YOUR PLUMBING CRASH COURSE: A GUIDE TO BATHTUB INSTALLATION

Your Plumbing Crash Course: A Guide to Bathtub Installation

Your Plumbing Crash Course: A Guide to Bathtub Installation

Blog Article

Website

They are making a few great annotation on the subject of How to Install a Bathtub Yourself in general in the article directly below.


Installing A Bathtub
Installing a bathtub isn't exactly brain surgery, yet it does require solid plumbing, woodworking, as well as often, tiling skills. Replacing an old bathtub with a new one is likewise a moderately difficult project. If the old tub is conveniently available, the project can relocate speedily; if you need to open up a wall to get rid of the old tub as well as position the brand-new bath tub, the job is much harder. In either instance, the job is within a residence handyman's abilities, although you will need a helper to leave the old bathtub and also set in the new one. Ensure you have qualified on your own for the work as well as fit trying it. Rather than employing a service provider to take over a halfway-completed task, it is much better to think about using one prior to you begin. Possibilities are you may need a specialist plumber to make tube links.
This post will help you mount a new tub in your restroom if you have already acquired a new tub and also do not require to transform the setup of your previous water pipelines.
Your devices as well as product list ought to make up the following:
  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Removing Old Touches


    If you require to replace old taps with new ones as a part of your setup, after that the first thing you must do is detach the water. After doing so, activate the faucets to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the restricted access that is usually the instance.
    Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth all set for the remaining water that will originate from the pipelines. Once the supply pipelines have actually been removed, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have been removed, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
    Before proceeding to fit the new faucets, contrast the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.

    Fitting New Taps


    If the tails of the new faucets are plastic, then you will require a plastic connector to prevent damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a connection to the current supply pipes.
    If you need to fit a monobloc, then you will call for lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
    Next off, place the tap in the mounting hole in the bath/basin guaranteeing that the washing machines remain in place between the tap as well as the sink. Protect the tap in place with the maker supplied backnut. As soon as the faucet is safely in place, the supply pipes can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal faucet adapters. The former type should be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been attached.

    Installing the Bathtub


    Using the two wood boards under its feet, put the bathtub in the called for placement. The wooden boards are valuable in evenly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 little points.
    The following goal is to make certain that the tub is leveled all round. This can be attained by examining the level as well as readjusting the feet on the tub till the spirit level reads level.
    To mount faucets, fit the bottom of the furthest adaptable tap port to the ideal supply pipe by making a compression sign up with; after that do the same for the various other faucet.
    Turn on the water supply and also examine all joints as well as new pipework for leakages as well as tighten them if required. Fill the tub and also examine the overflow electrical outlet as well as the normal outlet for leakages.
    Lastly, take care of the bath paneling as explained in the manufacturer's user's manual. Tiling and sealing around the tub must wait up until the tub has actually been utilized at the very least once as this will resolve it right into its final placement.

    Getting ready for the Installation


    To start with, the supporting framework provided with the bath ought to be fitted (if needed) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is necessary to make sure that if the tap features a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets device to stop strain on the bath tub.
    Fit the versatile faucet connectors to the bottom of both taps utilizing 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you make use of every one of the provided washers.
    Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to currently prepare to be suited its last setting.

    Tiling Around the Tub


    In the area where the bath meets the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to break a rigid seal, triggering the water to penetrate the wall in between the bathroom and the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling below.
    You can pick from a variety of coloured sealers to blend in your components and also installations. They are marketed in tubes and cartridges, as well as are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly load the bath tub with water prior to sealing, to enable the movement experienced when the tub is in use. The sealer can break rather early if you do not think about this activity prior to sealing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also conveniently readily available on the market. It is suggested to fit the ceramic tiles using water-resistant or water-proof glue and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    Do you appreciate reading about Installing A Bathtub? Make a review directly below. We will be pleased to hear your reactions about this article. We are looking forward that you come back again in the near future. Enjoyed our content? Please share it. Let other people locate it. Thank-you for your time invested reading it.


    Ensure top-quality plumbing repairs.

    Report this page